Gw-instek AFG-3000 Series User Manual Page 191
- Page / 304
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
REMOTE INTERFACE
191
<NRf+>
<Numeric>
NRf type with a
suffix including
MINimum,
MAXimum or
DEFault
parameters.
1, 1.5, 4.5e-1
MAX, MIN,
<aard>
Arbitrary ASCII
characters.
<discrete>
Discrete ASCII
character
parameters
IMM, EXT,
MAN
<frequency>
<peak deviation
in Hz>
<rate in Hz>
NRf+ type
including
frequency unit
suffixes.
1 KHZ, 1.0 HZ,
ΜHZ
<amplitude>
NRf+ type
including voltage
peak to peak.
VPP
<offset>
NRf+ type
including volt
unit suffixes.
V
<seconds>
NRf+ type
including time
unit suffixes.
NS, S MS US
<percent>
<depth in
percent>
NRf type N/A
Message
terminators
LF CR
line feed code (new line) and
carriage return.
LF
line feed code (new line)
EOI
IEEE-488 EOI (End-Or-Identify)
Note
^j or ^m should be used when using a terminal
program.
- Arbitrary Function Generator 1
- Table of Contents 3
- TABLE OF CONTENTS 5
- SAFETY INSTRUCTIONS 6
- Safety Guidelines 7
- GETTING STARTED 11
- Panel Overview 13
- Rear Panel 16
- QUICK REFERENCE 21
- How to use the Help Menu 24
- Selecting a Waveform 26
- Sine Wave 27
- Modulation 28
- FSK Modulation 30
- PWM Modulation 31
- ARB – Add Built-In Waveform 35
- ARB - Add Point 36
- ARB - Add Line 36
- ARB – Output Section 37
- ARB – Output N Cycle 37
- ARB – Output Infinite Cycles 38
- Utility Menu 39
- Interface GPIB 40
- Interface RS232 41
- Interface USB 41
- Menu Tree 42
- Waveform 43
- ARB-Display 43
- ARB-Edit 44
- ARB-Built in 45
- ARB- Built in- More 46
- ARB-Save 47
- ARB-Load 47
- ARB-Output 48
- QUICK REFERENCE 49
- Sweep - More 50
- Burst – N Cycle 51
- Burst - Gate 51
- UTIL - Interface 52
- Default Settings 53
- OPERATION 55
- Select a Waveform 56
- Setting a Square Wave 57
- Triangle Wave 58
- Setting the Pulse Width 59
- Setting a Ramp 60
- Noise Wave 61
- Setting the Frequency 61
- Setting the Amplitude 63
- Setting the DC Offset 64
- MODULATION 65
- Amplitude Modulation (AM) 67
- Selecting AM Modulation 68
- AM Carrier Shape 68
- Carrier Frequency 69
- Modulating Wave Shape 70
- AM Frequency 71
- Modulation Depth 72
- Frequency Modulation (FM) 75
- FM Carrier Shape 76
- FM Carrier Frequency 77
- FM Wave Shape 78
- Frequency Deviation 80
- Selecting FSK Modulation 84
- FSK Carrier Shape 84
- FSK Carrier Frequency 85
- FSK Hop Frequency 86
- FSK Rate 87
- FSK Source 88
- Pulse Width Modulation 90
- PWM Carrier Shape 91
- PWM Carrier Frequency 92
- PWM Modulating Wave Shape 92
- Modulation Duty Cycle 94
- PWM Source 95
- Frequency Sweep 97
- Selecting Sweep Mode 98
- Center Frequency and Span 100
- Sweep Mode 102
- Sweep Time 103
- Marker Frequency 104
- Sweep Trigger Source 105
- Trigger Output 106
- Burst Mode 108
- Burst Modes 109
- Selecting Burst Mode 109
- Burst Frequency 110
- Burst Cycle/Burst Count 111
- Infinite Burst Count 112
- Burst Period 113
- Burst Phase 115
- Burst Trigger Source 116
- Burst Delay 118
- Burst Trigger Output 119
- SECONDARY SYSTEM 121
- Save and Recall 122
- Modulation type 122
- GPIB Interface 125
- RS232 Interface 126
- RS232 Parity/Bit Settings 127
- USB Interface 128
- System and Settings 129
- Setting the output impedance 131
- Language Selection 132
- Setting the Sound Beep 133
- Screen Capture 134
- DSO Link 135
- ARBITRARY WAVEFORMS 137
- Inserting Built-In Waveforms 138
- Creating a Square Waveform 139
- Creating a Ramp Waveform 141
- Creating a Sinc Waveform 142
- Creating a DC Waveform 147
- Creating a Pulse Waveform 148
- Page Navigation (Back Page) 155
- Page Navigation (Next Page) 156
- Display 157
- Copy a Waveform 161
- Clear the Waveform 163
- ARB Protection 165
- Output an Arbitrary Waveform 168
- Output Markers 172
- New Folder: 176
- Load a Waveform from USB 180
- REMOTE INTERFACE 182
- Configure USB interface 183
- 1 2 3 4 5 184
- Configure GPIB interface 185
- Command Syntax 188
- NRf+ type 191
- SOURce[1]:OUTPut? 192
- Command List 193
- REMOTE INTERFACE 195
- System Commands 196
- SYSTem:VERSion? 197
- SYSTem:LANGuage 199
- Status Register Commands 200
- SYSTem:INTerface 203
- SYSTem:LOCal 203
- SYSTem:REMote 203
- Apply Commands 204
- Output Frequency 204
- 205
- SOURce[1]:APPLy:SINusoid 206
- SOURce[1]:APPLy:SQUare 206
- SOURce[1]:APPLy:RAMP 207
- SOURce[1]:APPLy:PULSe 207
- SOURce[1]:APPLy:NOISe 208
- SOURce[1]:APPLy:TRIangle 208
- SOURce[1]:APPLy:DC 209
- SOURce[1]:APPLy:USER 209
- 0~5V (50Ω) 210
- Example SOUR1:APPL? 210
- Output Commands 211
- SOURce[1]:FREQuency 212
- SOURce[1]:DCOffset 215
- {MINimum 216
- 3 volts 216
- SOURce[1]:RAMP:SYMMetry 217
- OUTPut:LOAD 218
- SOURce[1]:VOLTage:UNIT 219
- Pulse Configuration Commands 221
- SOURce[1]:PULSe:WIDTh 222
- AM Overview 223
- SOURce[1]:AM:STATe 224
- SOURce[1]:AM:SOURce 224
- SOURce[1]:AM:DEPTh 226
- Example SOUR1:AM:DEPT? 227
- +1.0000E+02 227
- FM Overview 228
- SOURce[1]:FM:SOURce 229
- SOURce[1]:FM:STATe 229
- SOURce[1]:FM:DEViation 231
- FSK Overview 233
- SOURce[1]:FSKey:STATe 233
- SOURce[1]:FSKey:SOURce 234
- SOURce[1]:FSKey:FREQuency 234
- PWM Overview 236
- SOURce[1]:PWM:STATe 237
- SOURce[1]:PWM:SOURce 237
- SOURce[1]:PWM:DUTY 239
- Frequency Sweep Commands 241
- SOURce[1]:SWEep:STATe 242
- SOURce[1]:FREQuency:STARt 243
- SOURce[1]:FREQuency:STOP 243
- SOURce[1]:FREQuency:CENTer 244
- SOURce[1]:FREQuency:SPAN 245
- SOURce[1]:SWEep:SPACing 245
- SOURce[1]:SWEep:TIME 246
- SOURce[1]:SWEep:SOURce 247
- OUTPut[1]:TRIGger:SLOPe 247
- OUTPut[1]:TRIGger 248
- SOURce[1]:MARKer:FREQuency 249
- SOURce[1]:MARKer 250
- Burst Mode Commands 251
- SOURce[1]:BURSt:STATe 253
- SOURce[1]:BURSt:MODE 253
- SOURce[1]:BURSt:NCYCles 254
- SOURce[1]:BURSt:PHASe 256
- OUTPut:TRIGger 261
- Arbitrary Waveform Commands 262
- Alternatively, the 262
- SOURce[1]:FUNCtion USER 263
- DATA:DAC 263
- SOURce[1]:ARB:EDIT:COPY 264
- SOURce[1]:ARB:EDIT:DELete 264
- SOURce[1]:ARB:EDIT:POINt 265
- SOURce[1]:ARB:EDIT:LINE 266
- SOURce[1]:ARB:EDIT:PROTect 266
- SOURce[1]:ARB:EDIT:UNProtect 267
- SOURce[1]:ARB:BUILt:SINusoid 267
- SOURce[1]:ARB:BUILt:SQUare 267
- SOURce[1]:ARB:BUILt:PULSe 268
- SOURce[1]:ARB:BUILt:RAMP 269
- SOURce[1]:ARB:BUILt:SINC 269
- SOURce[1]:ARB:BUILt:EXPRise 270
- SOURce[1]:ARB:BUILt:EXPFail 270
- SOURce[1]:ARB:BUILt:DC 271
- SOURce[1]:ARB:NCYCles 271
- SOURce[1]:ARB:OUTPut:MARKer 272
- SOURce[1]:ARB:OUTPut 272
- Save and Recall Commands 273
- MEMory:STATe:DELete ALL 274
- Error Messages 275
- Execution Errors 277
- ≤ max amplitude – Vpp/2 282
- Query Errors 287
- Arbitrary Waveform Errors 287
- SCPI Status Registers 289
- AFG-3000 Status System 290
- Questionable Status Register 291
- The Status Byte Register 293
- Output Queue 294
- Error Queue 294
- APPENDIX 295
- APPENDIX 297
- EC Declaration of Conformity 302
- INDEX 303
Related products and manuals for Equipment Gw-instek AFG-3000 Series
Equipment Gw-instek PCS-1000 User Manual
(93 pages)
(93 pages)
Equipment Gw-instek GPD-4303S User Manual
(59 pages)
(59 pages)
Equipment Gw-instek PPH-1503 User Manual
(137 pages)
(137 pages)
© 2020, manymanuals.com. All rights reserved. | 0.033 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals