GOS-6103C OSCILLOSCOPE USER MANUAL i CONTENTS PAGE 1. PRODUCT INTRODUCTION...1-1.Description…
GOS-6103C OSCILLOSCOPE USER MANUAL 15 (13)CH1 VOLTS/DIV. (14)CH2 VOLTS/DIV– Control knob for channel 1/channel 2 has double function. Turnin
GOS-6103C OSCILLOSCOPE USER MANUAL 17 Horizontal controls: The horizontal controls select the time base operation mode and adjust the horizon
GOS-6103C OSCILLOSCOPE USER MANUAL 19 coefficient (uncalibrated i.e. “DLY>0.125ms”). The width of the window segment decreases when the DE
GOS-6103C OSCILLOSCOPE USER MANUAL 21 coefficient (reduce the deflection speed) and the deflection coefficient becomes uncalibrated. Instea
GOS-6103C OSCILLOSCOPE USER MANUAL 23 When the setting (voltage) value is out of the changing portion of the observation waveform, the synch
GOS-6103C OSCILLOSCOPE USER MANUAL 25 (30)DELAY-HO—Control knob with a double function and associated LED. The control knob has two different
GOS-6103C OSCILLOSCOPE USER MANUAL 27 Measurement and Panel setting Control The measurement section controls the on-screen readout and the cu
GOS-6103C OSCILLOSCOPE USER MANUAL 29 (34) MEMO- 9 —SAVE/RECALL The instrument contains 10 non-volatile memories, which can be used by t
GOS-6103C OSCILLOSCOPE USER MANUAL 31 4-2.Rear Panel The rear panel provides input power and additional signal connections. (39)Line volt
GOS-6103C OSCILLOSCOPE USER MANUAL 33 5. OPERATION METHOD This section contains basic operation information and techniques that should be con
GOS-6103C OSCILLOSCOPE USER MANUAL iii FOR UNITED KINGDOM ONLY NOTE: This lead/appliance must only be wired by competent persons WARNING: TH
GOS-6103C OSCILLOSCOPE USER MANUAL 35 5-2.Connecting Input Signals Grounding The most reliable signal measurements are made when the oscillos
GOS-6103C OSCILLOSCOPE USER MANUAL 37 7. Observe the displayed waveform and compare them with the waveforms shown in figure 5-2. If either p
GOS-6103C OSCILLOSCOPE USER MANUAL 39 4. Set both CH1 and CH2 COUPLING to GND. 5. Use the CH1 and CH2 POSITION controls to align both traces
GOS-6103C OSCILLOSCOPE USER MANUAL 41 Displaying the sum or difference of CH1 and CH2 To display the algebraic sum or difference of CH1 and C
GOS-6103C OSCILLOSCOPE USER MANUAL 43 Setting up Dual X-Y Operation To use the oscilloscope in the dual X-Y mode, proceed the following steps
GOS-6103C OSCILLOSCOPE USER MANUAL 45 Magnifying Waveform Events Use the ×10 MAG pushbutton to view small portions of a waveform as which is
GOS-6103C OSCILLOSCOPE USER MANUAL 47 Figure 5-12(a) TV-V Figure 5-12(b) TV-H The polarity of the synchronization pulse is critical for
GOS-6103C OSCILLOSCOPE USER MANUAL 49 Figure 5-14: Cursor Measurement (a).Typical △V (Voltage difference) for AC voltage. When both CH1 a
GOS-6103C OSCILLOSCOPE USER MANUAL 51 (g).Typical △Θcursor function for phase measurement. A phase measurement is done by first setting a r
GOS-6103C OSCILLOSCOPE USER MANUAL 53 6.MAINTENENCE The following instructions are executed by qualified personnel only. To avoid electrical
GOS-6103C OSCILLOSCOPE USER MANUAL 1 1.PRODUCT INTRODUCTION 1-1. Description The GOS-6103C is a 100MHz, two-channel, dual-sweep, portable os
GOS-6103C OSCILLOSCOPE USER MANUAL 55 7.Block Diagram
GOS-6103C OSCILLOSCOPE USER MANUAL 3 7) Trigger signal output The signal selected by the TRIGGER SOURCE is available. This output may be use
GOS-6103C OSCILLOSCOPE USER MANUAL 5 Horizontal Modes MAIN(A), ALT, DELAY(B) A (main) Sweep Time 50ns~0.5s/DIV, continuously variable (UNCA
GOS-6103C OSCILLOSCOPE USER MANUAL 7 3.PRECAUTIONS BEFORE OPERATION 3-1.Unpacking the Oscilloscope The product has been fully inspected and t
GOS-6103C OSCILLOSCOPE USER MANUAL 9 4. PANEL INTRODUCTION After the instrument is switched on, all the important settings are displayed in t
GOS-6103C OSCILLOSCOPE USER MANUAL 11 4-1.Front Panel Display controls The display controls adjust the on-screen appearance of the waveform a
GOS-6103C OSCILLOSCOPE USER MANUAL 13 (7).20MHz BWL – Pushbutton with indicator LED. Briefly pressing the pushbutton, the bandwidth is reduce
Comments to this Manuals