Gw-instek GOS-630FC User Manual

Dual Trace Oscilloscope GOS-630FC USER MANUAL GW INSTEK PART NO. 82OS-630FCMA1 ISO-9001 CERTIFIED MANUFACTURER  This manual contains proprietary

PANEL OVERVIEW 19 Trigger Controls 1 Trigger ALT Switch Whenpressed,theTRIGALTswitchconstantlytogglesthetriggersourcebetweenCH1and

PANEL OVERVIEW 21 4 Trigger SLOPE Switch Selectsthetriggeringslope.Wheninthe“+”position(),theoscilloscopetriggerswhenthepositiveslo

PANEL OVERVIEW 23 Rear Panel Overview 21 3 41 FUSE & Line Voltage Selector HoldstheACmainsfuseandselectstheAClinevoltage,115Vor2

SETUP 25 CH1/CH2 VARIABLE Knob CALCH1/CH2 Coupling Switch ACTrigger SOURCE Switch CH1Trigger SLOPE Switch +(Positiveslope)TRIG ALT Switch

SETUP 27 6 Vertical adjustment UsetheCH1VOLTS/DIVknobandCH1verticalPOSITIONknobtoadjusttheverticalscaleandpositionofthewaveform.

MEASUREMENT 29 Dual Channel Measurement Steps 1. ConnectbothCH1andCH2signalstotheinputterminals. 2. Selecttheverticalcouplingbetw

MEASUREMENT 31 Waveform Addition/Subtraction Steps 1. MakesurebothCH1andCH2waveformsappearonthedisplay.Fordetails,seepage29. 2.

MEASUREMENT 33 5. ToadjusttheY‐axispositionanddeflection,usetheCH2verticalPOSITIONknob(position)andCH2VOLTS/DIVknob(deflection

FAQ 35 The input signal does not appear on the display. Checkthefollowingsettings.• ThecouplingmodeisnotsetattheGNDmode,inwhichth

APPENDIX 37 4. Ifnecessary,replacethefusethatisattachedtothefuseholder. 115230 5. Pushthefuseholderbackintothesocket. 230115

TABLE OF CONTENTS 3 Table of Contents SAFETY INSTRUCTIONS ... 5 PRODUCT OVERVIEW...

APPENDIX 39 Horizontal Axis Sweep time accuracy 0.2µS to 0.5S/DIV, ±3% x10MAG accuracy ±5% (20/50nS uncalibrated) Linearity ±3%, x10:±5% (20/50n

SAFETY INSTRUCTIONS 5 SAFETY INSTRUCTIONS Thischaptercontainsimportantsafetyinstructionsthatyoumustfollowwhenoperatingtheinstrumentand

SAFETY INSTRUCTIONS 7 Probeinput 600Vpeak ZAXISinput 30Vpeak (Measurement categories) EN 61010-1:2001 specifies the measurement categories

SAFETY INSTRUCTIONS 9 Power cord for the United Kingdom WhenusingtheinstrumentintheUnitedKingdom,makesurethepowercordmeetsthefollowin

PRODUCT OVERVIEW 11 Main Features High intensity and acceleration CRT TheCRTincorporateshighbeamtransmission,highintensity,anda2kVhigha

PANEL OVERVIEW 13 PANEL OVERVIEW Front Panel Overview Detaileddescriptionsofeachblock startfromthenextpage. Main Display Showsthewavef

PANEL OVERVIEW 15 LCD Display 1 CH1 Vertical Scale ShowstheCH1verticalscale.2 Horizontal Scale Showsthehorizontalscale.3 X-Y Mode When

PANEL OVERVIEW 17 Vertical Controls 1 654321 VOLTS/DIV Knob ControlstheCH1/CH2verticalscalefrom1mV/DIVto5V/DIVin12steps.2 Vertical PO